Frigidaire Washer vibrating excessively
Quick answer: Some vibration during spin is normal, but a washer that shakes, walks across the floor, or bangs against the cabinet has a balance or suspension problem.
- Unplug the washer before removing panels to inspect the suspension.
- Get help tilting or moving the washer; front loaders are extremely heavy and top heavy.
- A walking washer can strain and split its fill hoses; check them after any episode of heavy vibration.
Why is my washer vibrating so much?
Some vibration during spin is normal, but a washer that shakes, walks across the floor, or bangs against the cabinet has a balance or suspension problem. The most common causes are an unlevel machine, shipping bolts left in a new front loader, an unbalanced load, and worn shock absorbers or suspension rods. A weak floor or a broken counterweight can also let the drum move more than it should.
Our fitment data covers 919 Frigidaire washer models and 641 Frigidaire washer parts, so the part links below are filtered to this brand; always confirm your model number before ordering.
Most Likely Causes, in Order
1. Washer is not level or feet are loose
If one foot does not touch the floor firmly, the washer rocks on the other three and the whole cabinet amplifies every drum movement. Leveling feet also loosen over time and the lock nuts back off.
How to check: Push on opposite top corners of the washer; it should not rock at all. Place a level across the top front to back and side to side. Check that each foot's lock nut is tight against the base.
Fix: Adjust the feet until the washer is level and does not rock, then tighten the lock nuts. On top loaders with self-adjusting rear feet, tip the washer forward to let them reset. (Difficulty: Easy)
No Frigidaire part for this cause is in our catalog yet; search by your model number.
2. Shipping bolts still installed
New front loaders ship with long bolts through the back that lock the drum for transport. If they are not removed, the drum cannot float on its suspension and the whole machine shakes violently.
How to check: Look at the back panel for three or four large bolts with plastic spacers, usually near the drum. Press down on the drum from the front; it should move on its springs. This applies to any washer that was recently delivered or moved.
Fix: Remove the shipping bolts and spacers and plug the holes with the caps provided. Keep the bolts for future moves. (Difficulty: Easy)
No Frigidaire part for this cause is in our catalog yet; search by your model number.
3. Unbalanced or oversized load
A single heavy item like a bath mat or comforter, or a load that has bunched to one side, throws the drum off center. Overloading has the same effect because the clothes cannot redistribute.
How to check: Stop the washer during the shaking and look at how the load sits. Run an empty spin cycle; if it is smooth, the problem is the load and not the machine.
Fix: Wash heavy items with a few towels to balance them, do not fill the drum more than three quarters, and redistribute the load if the washer stops for imbalance. (Difficulty: Easy)
Matching Frigidaire parts:
- Washer Suspension Spring Retainer 137491600 — $43.02 · 10 models
- Washer Vertical Suspension Spring (Black) 137497110 — $31.66 – $45.51 · 4 models
- Washer Suspension Rod and Spring Assembly, Rear 5304511328 — $36.09 – $41.91 · 3 models
4. Worn shock absorbers or dampers on a front loader
Front loaders hang the drum on springs and rest it on two to four shock absorbers. As the shocks lose their damping, the drum swings freely and slams into the cabinet during spin.
How to check: Push the empty drum down hard and let go; it should stop moving almost immediately. Remove the front or rear panel and check the shocks for oil leaks, broken mounting pins, or a rod that slides with no resistance.
Fix: Replace all shock absorbers as a set. Also inspect the hanging springs for stretch or breakage. (Difficulty: Moderate)
No Frigidaire part for this cause is in our catalog yet; search by your model number.
5. Worn suspension rods on a top loader
Top loaders suspend the tub from four rods with damping cups at the top. When the cups wear, the tub sways during spin and hits the cabinet, and the washer may stop with an unbalanced error.
How to check: With the washer empty and off, push the tub to one side and release; it should return with little bounce. Remove the cabinet and check each rod for a cracked cup, worn ball, or bent rod. One bad rod is enough to cause the problem.
Fix: Replace all four suspension rods as a kit. (Difficulty: Moderate)
No Frigidaire part for this cause is in our catalog yet; search by your model number.
6. Loose or broken counterweight
Front loaders bolt heavy concrete or cast weights to the tub to keep it stable. If a bolt loosens or the weight cracks, the tub loses its balance and vibrates hard even with a normal load.
How to check: Remove the top panel and inspect the weights on the top and front of the tub. Try to move each one by hand; it should be rock solid. Look for concrete dust or cracks.
Fix: Tighten loose bolts to spec. Replace a cracked counterweight. (Difficulty: Moderate)
No Frigidaire part for this cause is in our catalog yet; search by your model number.
Other Frigidaire parts the catalog tags for this symptom
- Washer Outer Rear Tub Assembly 134956200 — $551.93 – $638.16 (noisy; rattling; tub off-balance)
- Tub 137492801 — $151.65 – $196.61 (noisy; rattling; tub off-balance)
Popular Frigidaire washer models
Confirm the model number on the rating plate before ordering. Each model page lists every compatible part.
Frequently Asked Questions
Why does my new front-load washer shake violently?
Almost always because the shipping bolts were not removed from the back. Remove them, then level the washer and make sure it does not rock.
Can the floor cause the washer to vibrate?
Yes. A springy wood floor or a washer on a pedestal amplifies movement. Placing the washer on a rigid piece of plywood or anti-vibration pads and locating it near a load-bearing wall helps.
My washer vibrates even when empty. What does that mean?
If an empty spin is rough after leveling, the suspension is worn or a counterweight is loose. Check the shocks or suspension rods next.
When to Call a Professional
Call a technician if the vibration continues after leveling and load changes, if you find a cracked counterweight or spider arm, or if you cannot safely tilt or open the machine to reach the suspension parts.