How to Install Dishwasher Dishrack Slide Rail 154597801 in a Galaxy Dishwasher
Quick answer: Open the door, remove the end stops at the front of the upper rack rails and slide the rack out. Unclip the worn rail from the tub side wall, hook 154597801 into the same slots with its stop toward the door, secure it, then roll the rack back in and check it glides fully without dropping.
The upper rack in a Galaxy dishwasher rides on a pair of slide rails fixed to the tub side walls. Each rack roller sits inside the channel of a rail, and the rail's front stop keeps the rack from rolling out onto the door. Part 154597801 is the replacement slide rail for these Frigidaire-built machines, and it also covers earlier numbers such as 154767502, 5304506530 and 5304532268. When a rail cracks, its stop breaks off or the channel wears wide, the upper rack sags to one side, jams halfway or drops off the rail when you pull it out to load glasses.
This is a quick job done entirely from inside the tub with the door open. There is no water or electrical work. The only fiddly part is releasing the old rail from the tub wall, which on these models uses a combination of hooks into keyhole slots and a screw or clip, and making sure the new rail is fully engaged before you trust it with a loaded rack. The same rail is listed for models like the FD1870WHB0, FDB949GFS1, GLD2555NDB0 and the Kenmore 58714131102.
See part details and every compatible model: 154597801
- Let the tub cool if a cycle just finished; the rails and tub wall hold heat.
- Wear gloves. A cracked rail has sharp plastic edges and the tub slots can cut.
- Switch the dishwasher off so a cycle cannot start with the rack out.
- Do not force a rail into its slots; a broken tub tab means a much larger repair.
Tools and Parts You Need
- Phillips screwdriver
- Small flat-blade screwdriver for the rail clips and end stops
- Flashlight
- Old toothbrush and vinegar for scale in the tub slots
- Towel
- Work gloves
Step-by-Step Installation
- Remove the upper rack Open the door fully and pull the upper rack out to its stop. Release the end stops at the front of each rail by flipping the tab or squeezing the clip, then roll the rack the rest of the way out and set it on a towel.
- Identify the failed rail Look at both rails on the tub side walls. Cracks usually appear near the front stop or at the rear mounting hook. Replace the damaged one; if both are worn, buy two.
- Release the old rail Remove the screw or press the retaining clip at the rail's front or rear, then slide the rail toward the rear so its hooks disengage from the keyhole slots in the tub wall. Lift it away.
- Clean the mounting slots Scrub scale and grease out of the tub slots with the toothbrush and vinegar so the new rail seats fully. Dry the area.
- Position 154597801 Hold the new rail with the channel opening toward the tub center and the front stop toward the door. Insert the hooks into the keyhole slots and slide the rail forward until it locks.
- Secure the rail Refit the screw or press the clip until it snaps. Tug the rail forward and back to confirm it cannot move.
- Reinstall the rack Line up the rack rollers with both rail channels and roll the rack in. Refit the end stops at the front of the rails.
- Test the glide Pull the rack fully out and push it in several times. It should run smoothly, stay level, and stop firmly at the front without lifting off the rail.
Fit Checks Before You Call the Job Done
- The rail hooks are fully engaged in the tub slots and the rail does not shift when pushed.
- The front stop faces the door and catches the rack roller.
- The rack rolls freely along the whole rail length without rubbing the tub wall.
- Both end stops are refitted and hold the rack on the rails.
- The rack sits level when fully out and does not tip forward.
Common Mistakes to Avoid
Installing the rail backwards With the stop at the rear, the rack rolls straight out onto the door. Stop goes toward the door.
Forgetting the end stops Without the stops the loaded rack drops off the rail the first time it is pulled out.
Leaving scale in the slots A rail that is not fully seated will pop out under load. Clean the slots first.
Replacing only one rail when both are worn A new rail on one side and a worn one on the other leaves the rack crooked and still jamming.
Prying the tub tabs The keyhole slots and tabs are part of the tub. Slide the rail to release it instead of levering.
Troubleshooting After Installation
Rack still jams halfway Check the rack rollers themselves for flat spots or cracks; worn rollers bind in a new rail.
Rack drops when pulled fully out An end stop is missing or the rail stop is facing the wrong way. Inspect and correct.
Rail pops loose during a cycle The hooks were not slid forward into the locked position. Remove and reseat.
Upper spray arm no longer spins The rack is sitting too low on one side and the water inlet is not docking. Confirm both rails are the same height and fully seated.
Care Tips After the Repair
- Do not lean on the pulled-out upper rack while loading; the front stop takes the load.
- Rinse scale from the rails and rollers every few months.
- Roll the rack in and out gently; slamming it cracks the front stop.
- Replace worn rollers when you replace a rail so the pair wears evenly.
Compatible Models (Sample)
This part is listed for 910 Galaxy models in our fitment data. Always confirm your exact model number on the appliance's rating plate.
Replaces or is replaced by: 154767502, 5304506530, 5304506531, 5304506916, 5304532268, 5304532269
Repair Difficulty and Time
Difficulty: Easy. Typical time: 15 to 30 minutes.
Frequently Asked Questions
Which dishwashers use slide rail 154597801?
It fits Frigidaire-built dishwashers sold under Galaxy, Frigidaire and Kenmore names, including the FD1870WHB0, FDB949GFS1, GLD2555NDB0, FGID2466QW2A and Kenmore 58714131102.
Is this rail for the left or right side?
Check your parts diagram; on many of these models the same rail number is used on both sides, mounted mirror-fashion.
My old rail was 5304506530. Is this the right part?
Yes. 154597801 replaces 5304506530, 5304506531, 5304506916, 154767502 and other earlier numbers.
Do I need to remove the lower rack?
No, but pulling it out gives more room to reach the rear rail hooks.
Final Checklist
- Dishwasher switched off and tub cool
- End stops released and upper rack removed
- Old rail unhooked from the tub slots
- Slots cleaned of scale
- 154597801 hooked in with the stop toward the door and secured
- Rack rollers aligned and rack reinstalled
- End stops refitted
- Glide tested fully in and out