How to Install Lid Hinge Mounting Screw WPW10119828 in a Whirlpool Washer

Quick answer: Unplug the Whirlpool washer and raise the lid to see the hinge where it meets the top panel. Hold the lid so the hinge plate sits flat with its holes lined up, start screw WPW10119828 by hand and tighten until the hinge is firm. Open and close the lid to confirm it swings true and hits the switch.

Lid hinge mounting screw WPW10119828 fastens the lid hinge to the top panel or the lid of a Whirlpool top-load washer, and it is shared across a huge family of Whirlpool-built machines, including Kenmore and KitchenAid units such as 11088675310, LTG6234DT1, GSQ9631LG0 and KAWS750JT0. Our fitment data lists 1131 models. When one of these screws backs out or strips, the lid sags to one side, drags on the top panel, closes crooked or stops pressing the lid switch, which on many of these washers means the machine will not spin.

This is a quick job but there are two things to get right. The hinge has to be aligned so the lid swings true before the screw is tightened, and the screw threads into thin painted sheet metal that strips if you overdo it. The guide below covers supporting the lid, lining up the hinge, driving the screw, and testing the lid switch afterward so the washer actually spins when you are done.

See part details and every compatible model: WPW10119828

⚠️ Safety First
  • Unplug the washer before working on the lid; the lid switch is wired to line voltage on many of these models and the lid area sits right over the tub.
  • Support the lid while a hinge screw is out. A lid held by one hinge can twist and bend the other hinge or drop on your fingers.
  • Turn off the water supply valves if you plan to tilt the washer or move it for access.
  • Watch for sharp edges on the top panel cutout under the hinge.

Tools and Parts You Need

  • Phillips screwdriver or nut driver to match the hinge screw head
  • Flashlight
  • Magnetic pickup or tape on the driver tip
  • Helper or a folded towel to support the lid while you work
  • Small wire brush to clean rust from the hinge area, optional

Step-by-Step Installation

  1. Unplug the washer Pull the plug from the wall outlet. If the washer sits under a counter or in a tight alcove, slide it forward enough to lift the lid fully.
  2. Inspect the hinge Raise the lid and look at both hinges where they meet the top panel and the lid. Find the empty, loose or stripped screw hole and check whether the hinge plate itself is bent.
  3. Support the lid Have a helper hold the lid, or prop it open on a folded towel, so the loose hinge is unloaded and the hinge plate can be moved into position.
  4. Clean the mounting area Wipe detergent residue or rust from around the hole. If the old screw is still there but stripped or broken, back it out or grip the shank with pliers and remove it.
  5. Align the hinge plate Press the hinge plate flat so it sits in its recess with all holes lined up. Check that the lid is centered in the top panel opening with an even gap on both sides before you put the screw in.
  6. Start WPW10119828 by hand Set the screw on the driver, held by a magnet or tape, and start it into the hole by hand so it follows the existing thread.
  7. Tighten snug Drive the screw until the hinge plate no longer moves and the head seats. Stop right there; the top panel metal strips easily.
  8. Test the lid and the switch Open and close the lid several times. It should swing without rubbing and land square. Plug the washer in, start a spin cycle with the lid closed and confirm the tub spins, which proves the lid switch is being pressed.

Fit Checks Before You Call the Job Done

  • The hinge plate sits flat in its recess with no gap under it.
  • The lid is centered in the opening with an even gap on both sides.
  • The lid swings freely without scraping the top panel or the other hinge.
  • The lid closes flat and presses the lid switch, and the washer spins with the lid closed.
  • The screw head is flush and does not catch on the lid as it opens.

Common Mistakes to Avoid

Tightening before the lid is aligned Once the screw is snug the hinge is locked in place. Center the lid first, then tighten.

Overtightening The screw goes into thin sheet metal. One turn too many strips the hole and the hinge loosens again in a week.

Working with the lid unsupported The weight of a hanging lid bends the remaining hinge and misaligns everything.

Ignoring the other hinge If one screw came loose, check the screws on the other hinge too while the lid is up.

Using a longer generic screw A longer screw can poke through into the lid switch wiring or the tub ring. Use WPW10119828.

Troubleshooting After Installation

Washer fills but will not spin after the repair The lid is not pressing the lid switch. Check that the lid closes flat and centered; loosen the hinge screws slightly, realign, and retighten.

Screw spins without tightening The hole is stripped. Use a speed nut behind the panel or go up one screw size, keeping the length the same.

Lid still sags or rubs The hinge plate is bent or the other hinge is loose. Straighten or replace the bent hinge and check every screw.

Lid squeaks after the job Detergent residue or rust on the hinge pivot. Clean it and apply a small amount of silicone lubricant to the pivot, not to the screw.

Care Tips After the Repair

  • Do not let the lid slam; that impact is what works hinge screws loose.
  • Wipe detergent and bleach spills off the top panel before they corrode the hinge area.
  • Check both hinges for tightness every few months.
  • Do not lean on or set heavy items on the open lid.

Compatible Models (Sample)

This part is listed for 1131 Whirlpool models in our fitment data. Always confirm your exact model number on the appliance's rating plate.

Repair Difficulty and Time

Difficulty: Easy. Typical time: 10 to 20 minutes.

Frequently Asked Questions

Which washers use lid hinge screw WPW10119828?

Our fitment data lists 1131 Whirlpool-built top-load washers under the Whirlpool, Kenmore and KitchenAid names, including 11098573120, LSQ9010KT0 and 7MLSR7533PQ0. Confirm your model on the label under the lid.

Why will my washer not spin after I fixed the hinge?

A misaligned lid does not press the lid switch, and the washer refuses to spin as a safety measure. Realign the hinge so the lid closes flat and centered.

Do I need to remove the top panel or cabinet?

No. The hinge screws are reached with the lid raised. Only if a screw broke off flush might you need to lift the top panel to get behind it.

Final Checklist

  • Washer unplugged
  • Loose or stripped hinge screw hole identified
  • Lid supported while the hinge is loose
  • Mounting area cleaned and old screw removed
  • Lid centered and hinge plate flat before fastening
  • WPW10119828 started by hand and driven just snug
  • Lid swings freely and closes square
  • Spin cycle tested with the lid closed

Related Repair Guides