How to Install Range Screw WPW10067840 in a Whirlpool Range

Quick answer: Switch off power to the Whirlpool range, locate the trim, panel or bracket that is missing its screw, and confirm WPW10067840 matches the fasteners beside it. Seat the part on its tabs, start the screw by hand in the existing hole and tighten until the part is firm, stopping before the metal strips.

Range screw WPW10067840 is a fastener used on Whirlpool-built ranges and wall ovens, including Maytag models such as MER7662WS0, WFG361LVS3, WEG745H0FH0 and YWEE750H0HW4. It replaces the earlier numbers W10619020 and W11804917. Our fitment data lists 76 models. Like most appliance screws, it is used at more than one position: oven door trim and handle brackets, control panel and backguard trim, cabinet side panels and the small brackets that hold internal components in place.

People usually order this screw after a door handle or trim piece works loose, after a repair where the original screw was lost, or after the original was stripped by an impact driver. The guide below shows how to identify the right position, how to reach it safely on a range that has line voltage behind the control panel and heat around the oven, and how to seat the screw firmly without wrecking the threads in the cabinet metal.

See part details and every compatible model: WPW10067840

⚠️ Safety First
  • Unplug the range or switch off its breaker before touching screws on the control panel, backguard or inside the cabinet.
  • Let the oven cool fully before working on the door, handle or any trim near the cavity.
  • Support the oven door if you must loosen door screws; a door that swings open unexpectedly can pinch fingers or crack glass.
  • On gas ranges, no gas work is needed, but keep hands clear of the burner tubing when reaching inside.

Tools and Parts You Need

  • Phillips screwdriver or nut driver matching the neighboring screw heads
  • Flashlight
  • Magnetic pickup or a bit of tape on the driver tip
  • Painter's tape to protect the door or trim finish
  • A photo of the original screw or the parts diagram for your model

Step-by-Step Installation

  1. Cut power Unplug the range or turn off its breaker. Confirm the display is dark and the oven is cool.
  2. Identify the position Find the loose trim, handle bracket or panel and the empty or damaged hole. Note how the remaining screws enter and which parts they pass through.
  3. Match the screw Compare WPW10067840 with a neighboring screw on the same part. If the head and thread match, it belongs there. If your diagram lists W10619020 or W11804917, this is the same screw.
  4. Gain access Remove the backguard cover, drawer or trim piece that hides the hole so you can drive the screw straight. For door screws, support the door or remove it if the manual shows that step.
  5. Seat the part Hook the part on its tabs or locating pins so the hole lines up naturally. Do not draw the part into place with the screw.
  6. Start by hand Place the screw on the driver and turn it in by hand until it follows the existing thread. If it resists, back out and try again straighter.
  7. Tighten snug Drive the screw until the part is firm and the head seats. Stop immediately; extra torque strips the cabinet metal.
  8. Reassemble and test Refit any covers, restore power, and check the display. Open and close the oven door, pull on the handle and confirm the trim is solid with no rattle.

Fit Checks Before You Call the Job Done

  • The screw follows the existing thread by hand without forcing.
  • The head seats flat and the part is flush with the surrounding trim.
  • Door handle and trim do not move when pulled firmly.
  • No wire was pinched and the display works after power is restored.
  • Other screws on the same part were checked and are tight.

Common Mistakes to Avoid

Using an impact driver Impact tools strip range cabinet screws instantly. Use a hand screwdriver or a drill on its lowest clutch setting.

Leaving the door unsupported Loosening door trim screws with the door hanging open can let it drop or twist the hinges. Support it or remove it.

Overtightening Snug is finished. One more turn and the hole is ruined.

Drawing the part into place with the screw Seat the tabs first, then fasten. Otherwise the part sits crooked and the screw sits at an angle.

Skipping the power disconnect Backguard and control panel screws sit next to live wiring. Cut power first.

Troubleshooting After Installation

Screw spins and never tightens The hole is stripped. Use a speed nut behind the panel, go up one screw size, or use the alternate hole if the part has one.

Handle or trim still loose A second screw on the part is also loose, or a hidden bracket behind the trim has shifted. Remove the trim and check the bracket.

Screw will not start Holes are misaligned or there is debris in the thread. Reseat the part and clear the hole.

Door does not close squarely after the job The door trim or hinge area was disturbed. Loosen the trim screws slightly, close the door to align everything, then retighten.

Care Tips After the Repair

  • Check handle and trim screws every few months; they take the most daily force.
  • Do not lift or lean on the oven door handle; it loosens the handle brackets.
  • Wipe grease off door trim so it does not seep behind the fasteners.
  • Keep spare screws in a labeled bag in the storage drawer.

Compatible Models (Sample)

This part is listed for 76 Whirlpool models in our fitment data. Always confirm your exact model number on the appliance's rating plate.

Replaces or is replaced by: W10619020, W11804917

Repair Difficulty and Time

Difficulty: Easy. Typical time: 10 to 20 minutes.

Frequently Asked Questions

Where is WPW10067840 used on my range?

At several positions, commonly door trim and handle brackets, control panel trim, side panels and small internal brackets. Match it to the screws still holding the loose part.

Which models use WPW10067840?

Our fitment data lists 76 Whirlpool and Maytag ranges and wall ovens, including JDS1750ML1, RF367LXSS2 and MER7662WS0. It replaces W10619020 and W11804917.

Can I use a hardware store screw instead?

Not recommended. Length, thread pitch and head style matter on thin cabinet metal and near hot parts. Use the listed screw.

Final Checklist

  • Range unplugged or breaker off, oven cool
  • Loose trim, bracket or panel and empty hole identified
  • WPW10067840 compared to neighboring screws
  • Door supported if door screws are involved
  • Part seated on its tabs before fastening
  • Screw started by hand and tightened just snug
  • Covers refitted, power restored, handle and trim tested

Related Repair Guides