How to Install Screw WPW10031790 in a Whirlpool Range

Quick answer: Cut power to the Whirlpool range, find the part that lost its screw and confirm WPW10031790 matches the neighboring fasteners. Hold the panel, bracket or trim in place with its tabs engaged, start the screw by hand in the existing hole, and tighten until the part is firm without stripping the metal.

Screw WPW10031790 is a cabinet and trim fastener used on Whirlpool-built ranges, including many Maytag models such as JGS1450FS0, WEG745H0FH0, JDS1750ML1 and RF367LXSS2. It is the current replacement for a long list of older numbers, among them W10541911, W10817436, W10876582, W11100619 and W11339500, so if a parts diagram for your range lists one of those, this is the screw to buy. Our fitment data covers 82 models, and the same screw also appears on some wall ovens, dryers and freezers from the same manufacturer.

Because it is used at many positions, the guide below does not assume a single location. Typical spots on a range are the control panel and backguard trim, the oven door trim, side and rear cabinet panels, storage drawer parts and small brackets inside the cabinet. The job is simple, but the surroundings on a range are not: line voltage behind the control panel, sharp cabinet edges and thin sheet metal that strips easily. Follow the steps in order and the repair takes minutes.

See part details and every compatible model: WPW10031790

⚠️ Safety First
  • Unplug the range or turn off its breaker before working on the control panel, backguard, rear panel or anything inside the cabinet.
  • Make sure the oven and cooktop are off and cool; door trim and cabinet panels near the oven get hot.
  • On a gas range, no gas work is needed, but do not disturb the gas line or burner tubing while reaching inside.
  • Wear gloves when reaching behind panels; the cabinet edges are sharp.

Tools and Parts You Need

  • Phillips screwdriver or nut driver to match the head of the neighboring screws
  • Flashlight
  • Magnetic pickup or tape on the driver tip
  • Painter's tape to protect visible trim
  • Your range's parts diagram or a photo of the original screw

Step-by-Step Installation

  1. Confirm the part number If you ordered from an older diagram, check that the number listed there is one WPW10031790 replaces, such as W10541911 or W11162113. That confirms you have the right fastener.
  2. Cut power Unplug the range or switch off its breaker and confirm the display is dark.
  3. Locate the empty position Find the loose panel, trim or bracket and identify the empty or stripped hole. Look at the screws still holding the same part and note the direction they enter.
  4. Compare with neighbors Hold WPW10031790 next to a neighboring screw. Thread and head should match. If they differ, the empty hole may belong to a different fastener.
  5. Open up access Remove the backguard cover, storage drawer or side trim as needed so you can see the hole squarely and get the driver in straight.
  6. Align the part Seat the part on its hooks or tabs first so the hole lines up naturally. Never use the screw to pull a part into place.
  7. Start and drive the screw Start the screw by hand until it picks up the existing thread, then tighten until the part is firm and the head seats. Stop as soon as it is snug.
  8. Reassemble and test Refit any cover you removed, restore power and confirm the display comes on. Open and close the oven door and check that nothing rattles.

Fit Checks Before You Call the Job Done

  • The screw threads in by hand without forcing.
  • The head sits flat against the part with no gap.
  • The part is firm and flush with adjoining panels or trim.
  • No wire is pinched behind the part and the display works after power is restored.
  • Neighboring screws on the same part were checked and are tight.

Common Mistakes to Avoid

Skipping the power disconnect Control panel and rear panel screws sit next to line-voltage wiring. Cut power first.

Pulling the part into place with the screw This bends the part and strips the hole. Seat the tabs first, then drive the screw.

Overtightening Range sheet metal strips with little extra force. Snug is finished.

Assuming every screw is the same A range uses several fastener types. Compare WPW10031790 with the neighbors before driving it.

Scratching the finish A slipped driver marks stainless and painted trim. Mask around visible screws.

Troubleshooting After Installation

Screw spins without gripping The hole is stripped. Fit a speed nut behind the panel or move up one screw size.

Part still rattles Another fastener on the same part is loose, or the tabs are not engaged. Check all of them.

Screw will not start The holes are misaligned or the wrong screw is being used. Reseat the part and compare the screw with its neighbors.

Display dead after reassembly A wire was disturbed behind the control panel. Cut power, open the panel and reconnect it.

Care Tips After the Repair

  • Check trim and panel screws whenever you pull the range out to clean.
  • Close the oven door gently; slamming loosens trim fasteners over time.
  • Keep grease off the backguard so it does not seep into screw holes.
  • Keep spare screws in a labeled bag in the storage drawer.

Compatible Models (Sample)

This part is listed for 82 Whirlpool models in our fitment data. Always confirm your exact model number on the appliance's rating plate.

Replaces or is replaced by: 0690406A12, 141-2-853T-76200, 2159073, 32548276, A5484539, G501-0077-W1, TXAJTA7S8J, W10541911

Repair Difficulty and Time

Difficulty: Easy. Typical time: 10 to 20 minutes.

Frequently Asked Questions

My parts diagram lists a different number. Is WPW10031790 still correct?

If the diagram lists W10541911, W10817436, W10876582, W10909682, W11100619, W11162113, W11339500 or another number in its replacement list, yes. This is the current part.

Which appliances use WPW10031790?

Our fitment data lists 82 Whirlpool and Maytag models including SF380LEPT3, WEG750H0HB0 and JGS1450FS0, and the same screw appears on some wall ovens, dryers and freezers.

Do I have to unplug the range for a cosmetic trim screw?

Yes, if the screw is on the control panel, backguard, rear panel or inside the cabinet. Purely external door trim can be done with the range cool and switched off, but unplugging costs nothing.

Final Checklist

  • Old part number confirmed in the WPW10031790 replacement list
  • Range unplugged or breaker off
  • Empty hole and loose part identified
  • Screw compared with its neighbors
  • Part seated on its tabs before the screw goes in
  • Screw started by hand and driven just snug
  • Covers refitted, power restored, display and door checked

Related Repair Guides