How to Install Range Hood Light Lens WB02X11024 in a GE Range

Quick answer: Switch the hood light off and let the bulb cool. Slide or unclip the old lens from the underside of the hood, wipe the opening, then seat WB02X11024 so its tabs or lip lock into the frame. Turn the light on to confirm it sits flat.

The light lens WB02X11024 is the clear cover under the range hood above your GE range. It protects the bulb from grease, steam and knocks from pots. When the lens yellows, cracks or falls out, the bulb is left exposed and the hood looks tired. GE lists this lens for hood models such as JV347H1CC, JV347H1WW and JV367H1BB, and it replaces the older codes WX10X117, WX10X119, WX10X3030 and WX10X392.

This is one of the easiest repairs on a range hood. No wiring is touched and most people finish in under half an hour. The trick is understanding how the lens is held on your hood: some frames use a sliding channel, others use spring tabs that snap into slots. Once you see how the old lens comes out, the new one goes in the same way.

See part details and every compatible model: WB02X11024

⚠️ Safety First
  • Turn the hood light off and let the bulb cool for at least ten minutes; halogen bulbs stay very hot.
  • Stand on a stable step stool, never on the range top or oven door.
  • Do not cover the bulb with anything other than the correct lens; an improvised cover can overheat.
  • Wear gloves when reaching into the hood cavity because stamped metal edges can be sharp.

Tools and Parts You Need

  • Step stool that lets you work at eye level with the underside of the hood
  • Small flat-blade screwdriver for releasing a stuck lens tab
  • Phillips screwdriver in case your hood frame uses retaining screws
  • Soft microfiber cloth and mild degreaser
  • Work gloves to protect your hands from sharp sheet metal edges
  • Flashlight to inspect the lens channel and bulb socket

Step-by-Step Installation

  1. Kill the light and let it cool Switch off the hood light and give the bulb time to cool. If the bulb is halogen, wait a full ten minutes because the glass stays hot long after the light is off.
  2. Study how the old lens is held Look at the underside of the hood with a flashlight. Note whether the lens rides in a channel and slides toward the back, or has spring tabs that sit in slots on the frame. Take a photo so the new lens goes in the same orientation.
  3. Release the old lens For a sliding lens, push it toward the rear of the hood until the front lip clears the frame, then lower the front edge and pull it out. For a tabbed lens, press one tab inward with your thumb or a flat screwdriver and lower that corner first.
  4. Clean the opening and check the bulb Wipe grease from the frame channel and around the bulb socket. A dirty channel makes the new lens hard to seat. Replace the bulb now if it is dim or blackened, since you already have access.
  5. Orient the new lens Hold WB02X11024 up to the opening and match the shape to your photo. The textured side usually faces down toward the room, and any raised lip or tabs face the frame.
  6. Seat the lens For a sliding frame, angle the rear edge into the channel first, then lift the front edge and slide the lens forward until it stops. For a tabbed frame, insert one side, flex the lens slightly and let the tabs snap into their slots.
  7. Press the perimeter home Run your fingers around the edge of the lens and press gently. It should sit flush with the hood frame with no gap and no rocking.
  8. Test the light Turn the hood light on and off a few times. Look for even illumination and confirm nothing rattles when you run the fan on high.

Fit Checks Before You Call the Job Done

  • Lens sits flush with the frame on all four sides with no visible gap
  • Lens does not shift or drop when you tap the hood lightly with your palm
  • No rattle when the hood fan runs on its highest speed
  • Light spreads evenly across the range top without a dark corner
  • The lens code WB02X11024 matches your hood model, and the shape matches the old lens you removed

Common Mistakes to Avoid

Forcing the lens in backwards The tabs or lip only engage in one orientation. If the lens will not seat with light pressure, flip it rather than pushing harder and cracking it.

Skipping the cleaning step Grease in the frame channel is the usual reason a new lens will not slide home. Two minutes with a degreaser saves a lot of frustration.

Using the wrong lens A lens from another hood family may look similar but be a few millimetres off. WB02X11024 is the current code for the older WX10X117, WX10X119, WX10X3030 and WX10X392 lenses.

Leaving the lens loose on one side A half-seated lens will vibrate free the first time the fan runs on high. Press every edge and listen for the tab to click.

Troubleshooting After Installation

Lens will not slide all the way into the channel Remove it and clean the channel again. Check that no old broken tab or grease clump is lodged in the track.

Lens rattles when the fan runs One tab is not engaged. Remove the lens, inspect the tabs for damage, and reseat it so all tabs click into their slots.

Light looks dim after the new lens is installed The lens does not affect brightness much. Replace the bulb with the wattage printed on the hood label and clean the reflector behind the socket.

Care Tips After the Repair

  • Wipe the lens weekly with a soft cloth and mild dish soap so grease does not bake on.
  • Never use abrasive pads or solvent cleaners on the lens; they scratch and cloud the plastic.
  • Run the hood fan during frying and boiling so heat and steam leave the hood cavity quickly.
  • Check the lens tabs once a year when you clean the grease filters and reseat it if it feels loose.

Compatible Models (Sample)

This part is listed for 18 GE models in our fitment data. Always confirm your exact model number on the appliance's rating plate.

Replaces or is replaced by: WX10X117, WX10X119, WX10X3030, WX10X392

Repair Difficulty and Time

Difficulty: Easy. Typical time: 10 to 20 minutes.

Frequently Asked Questions

Does WB02X11024 fit my GE range hood?

It is listed for GE hood models including JV347H1CC, JV347H1WW, JV347H2BB, JV347H1BB, JV367H1BB and JV247P1WW, and it replaces WX10X117, WX10X119, WX10X3030 and WX10X392. Confirm your model number on the label inside the hood.

Do I need to unplug the hood to change the lens?

No wiring is touched, so switching the light off and letting the bulb cool is enough. If you also change the bulb, turning the hood off at the breaker is a sensible extra step.

Can I run the hood without a lens for a while?

You can, but the bulb will collect grease fast and is more likely to break from a knock. Fit the new lens as soon as it arrives.

How do I clean a yellowed lens?

Warm water with dish soap removes grease film. If the plastic itself has yellowed from heat, cleaning will not restore it and a new WB02X11024 is the fix.

Final Checklist

  • Hood light off and bulb cool before starting
  • Photo taken of how the old lens was oriented
  • Frame channel and tabs cleaned of grease
  • New lens WB02X11024 oriented with tabs or lip toward the frame
  • All edges pressed flush with no gap
  • Light tested on and off, fan tested on high with no rattle

Related Repair Guides