How to Install Icemaker Mold 5304456665 in a Frigidaire Refrigerator

Before You Start

An icemaker mold shapes the water into cubes during the freeze cycle. When the mold fails, the icemaker may not release ice well. It may also form partial cubes or stop producing ice at all. Since your symptom list only states “refrigerator not working properly,” treat this repair as one focused check in the ice system.

Do not assume every ice problem comes from the mold. A refrigerator can have water supply issues, temperature issues, door sealing problems, or control problems. You should inspect the area before replacing any part.

Start by checking three basic things:

• The refrigerator has power.
• The freezer section feels cold enough to make ice.
• The icemaker area has no major ice blockage.

If the freezer is warm, fix the cooling problem first. A new mold will not help if the unit cannot freeze water.

If the freezer is cold and the icemaker looks worn, stained, cracked, or rough, the mold becomes a stronger suspect. You can move forward with the repair after you confirm the model and part.

Compatible Frigidaire Refrigerator Models

Use only the compatibility information you have. For this repair, I can only list these models:

Check the model number on your refrigerator before you buy or install the mold. The model tag is often inside the fresh food section, near a side wall or liner area. Some units place it near the door frame.

Read the full model number, not just the first few characters. One letter or number can change the correct part. If your model is not listed above, you need to verify fit before installing part 5304456665.

Tools and Supplies

Your exact fasteners may vary by model. Do not force any screw or clip. Use the tool that fits the part in front of you.

Helpful tools and supplies:

• Work gloves
• Towel
• Small container for screws
• Nut driver set
• Phillips screwdriver
• Flat screwdriver or plastic pry tool
• Flashlight
• Phone camera for reference photos

Keep the phone camera handy. A quick photo before each step can save you time during reassembly. Take pictures of wire routing, brackets, and the old mold position.

Do not use sharp tools near plastic parts unless you have no other option. Plastic liners and icemaker housings can crack when pried too hard.

Safety First

Unplug the refrigerator before you work inside the icemaker area. You may work near wiring, a motor, and moving parts. Power must stay off until you finish the installation.

If your refrigerator is hard to move, do not yank it forward. Pulling too hard can damage flooring or water lines. If you cannot reach the power cord safely, turn off power at the breaker.

Also shut off the water supply if your icemaker setup allows it. You do not want water entering the icemaker while parts are removed. Place a towel under the work area to catch drips or loose ice.

Follow these safety points:

• Keep your hands clear of sharp metal edges.
• Do not touch bare wires.
• Do not work with wet hands near electrical parts.
• Do not force frozen parts loose.
• Let ice soften before removing stuck pieces.

If you see burned wiring, melted plastic, or a heavy leak, stop. That repair needs more diagnosis before you install the new mold.

How to Install Icemaker Mold 5304456665 Safely

What Good Installation Looks Like

A good mold installation should feel secure. The mold should not shift or wobble. The icemaker should sit level in its mounting area.

You should see:

• No loose screws
• No pinched wires
• No cracked plastic supports
• No water dripping into the freezer
• No ice bin blockage
• No odd rubbing noise during movement

The first ice batch may take time. That depends on freezer temperature, usage, door openings, and the icemaker cycle. Be patient before judging the repair.

If the refrigerator still does not work properly after the repair, broaden your checks. The issue may sit outside the mold.

Common Mistakes to Avoid

Most failed icemaker repairs come from rushing. The part may be correct, but the install can still cause trouble.

Avoid these mistakes:

Here is a simple pitfall ranking from a repair bench view:

The top two matter most. A wrong part or pinched wire can create a bigger problem than the original symptom.

When the Mold Is Not the Real Problem

A bad mold is not the only reason an icemaker acts up. If your Frigidaire refrigerator is not working properly, check the whole ice path.

The mold may not be the main fault if:

• No water reaches the icemaker.
• The freezer feels too warm.
• The icemaker never starts a cycle.
• The ice bin area has heavy frost.
• The water fill area freezes shut.
• The unit has a wiring or control issue.

If the freezer temperature is not cold enough, the icemaker cannot make firm cubes. If water does not enter, the mold has nothing to freeze. If the icemaker drive parts fail, a new mold may not eject ice.

Use the mold condition as one clue, not the only clue.

Install Difficulty and Time

This repair is rated medium. Most careful DIY users can handle it if they work slowly and stay organized.

Expected time: 30 to 60 minutes.

You may need more time if:

• The icemaker area has heavy ice buildup.
• Screws are hard to reach.
• The refrigerator is packed with food.
• You need extra time to photograph each step.
• The harness connector is tight.

Do not rush the job to meet the time estimate. A clean 75-minute repair beats a cracked part in 30 minutes.

Quick Decision Table

Use this table before you replace the icemaker mold.

This table helps you avoid part swapping. Good repair work starts with a clear reason.

Testing After Installation

After you restore power, listen for normal refrigerator operation. Then check the icemaker area over the next several hours.

Look for water leaks first. Leaks can freeze fast inside the freezer. Even a small drip can create ice buildup around the bin or icemaker.

Check the ice bin after the unit has had enough time to cycle. If you get ice, inspect the cubes. They should look formed enough for normal use.

If the first batch looks odd, discard it and check again later. The system may need one cycle to settle after service.

If no ice appears, do not remove the mold again right away. Check power, temperature, water supply, and the icemaker shutoff position.

Care Tips After the Repair

A new mold works best when the freezer stays clean and stable. You can prevent repeat trouble with a few habits.

Keep the freezer door closed as much as possible. Warm air creates frost. Frost can affect the ice bin, fill area, and moving parts.

Do not overfill the freezer near the icemaker. Food packages can block airflow or push against the ice bin.

Dump old ice if it clumps together. Clumped ice can jam the bin and make you think the icemaker failed again.

Check the icemaker area once a month. Look for frost buildup, loose ice pieces, or water stains. Small signs help you catch bigger problems early.

What to Do Next

Need help finding the right part for your Frigidaire refrigerator?

• Contact RepairKitHub
• Find Your Parts
• Subscribe to Weekly DIY Guide

Final Repair Checklist

Before you call the job done, run through this checklist:

• You confirmed the refrigerator model number.
• You confirmed OEM part 5304456665.
• You unplugged the refrigerator before service.
• You shut off water if needed.
• You removed ice and loose debris.
• You photographed wire and bracket locations.
• You installed the mold without forcing it.
• You kept wires clear of moving parts.
• You reinstalled all covers and brackets.
• You checked for leaks after restoring power.
• You discarded the first ice batch.

If each item checks out, your repair is in good shape.

FAQ

Related Repair Guides

• Frigidaire parts catalog
• Why is my Frigidaire appliance temperature issue?
• Why is my Frigidaire appliance odor issue?
• Why is my Frigidaire appliance rust/corrosion?
• How to Install Light Socket 241622802