How to Install Appliance High-Temperature Adhesive 5308027429 in a Frigidaire Dryer
Quick answer: Unplug the dryer, open the cabinet to expose the drum bulkheads, strip the old felt and glue residue to bare metal, lay a thin continuous bead of 5308027429, press the new felt seal in place, let it cure fully per the tube instructions, then reassemble and run an empty air-fluff cycle.
Appliance high-temperature adhesive 5308027429 is the glue Frigidaire specifies for bonding felt drum seals, foam gaskets and similar soft parts inside a dryer. Ordinary contact cement softens once the drum gets warm and the seal walks out of position within a few loads. This product is formulated to hold its bond at operating temperature so the felt stays put where it rides against the spinning drum.
You will reach for this adhesive when replacing a worn felt drum seal or duct seal on Frigidaire and Kenmore-built dryers such as FGR6600FS0, AGQ8700FS0 or WDG336REW0. Installing it means preparing the metal, laying it down correctly and letting it cure before the drum turns. The instructions packed with the tube govern working and cure times, so read them first.
See part details and every compatible model: 5308027429
- Unplug the dryer or switch off its breaker before opening the cabinet; on gas models close the gas valve.
- Work in a ventilated area and keep the adhesive away from open flame and the pilot or igniter of a gas dryer.
- Wear gloves; the adhesive is difficult to remove from skin and metal edges inside the cabinet are sharp.
- Keep the tube capped between applications and out of reach of children and pets.
Tools and Parts You Need
- Quarter-inch nut driver for cabinet screws
- Putty knife or plastic scraper for removing old felt
- Wire brush or coarse abrasive pad for glue residue
- Rubbing alcohol or a degreasing wipe for final surface cleaning
- Disposable gloves and shop rags
- Spring clamps or masking tape to hold the felt while it sets
Step-by-Step Installation
- Disconnect power and open the cabinet Unplug the dryer, pull it out from the wall and remove the top panel and front panel screws so the drum and bulkheads are exposed. On many Frigidaire models the front panel lifts off after the lower screws are removed and the panel is tilted forward.
- Remove the drum if the seal is on the rear bulkhead Release the belt tension at the idler pulley, slip the belt off the motor and lift the drum out of the cabinet. The felt seal path on the rear bulkhead and the front drum glide area are now fully accessible.
- Strip the old felt and adhesive Peel away the old felt, then scrape every trace of dried glue with a putty knife. Follow with a wire brush or abrasive pad until you are down to clean metal; new adhesive will not hold on top of old adhesive.
- Clean and dry the bonding surface Wipe the entire seal path with rubbing alcohol to remove lint dust and oil from your hands. Let it flash off completely so the surface is bone dry before any adhesive touches it.
- Lay a thin continuous bead Cut the tube tip small and run one unbroken bead of 5308027429 along the center of the seal path. A thin line is correct; a heavy bead squeezes out, stays soft and can catch lint against the drum.
- Seat the felt seal Start the felt at one point and press it into the bead as you work around the circle, keeping the edge aligned so the pile faces the drum. Where the two ends meet, overlap them slightly so there is no gap for air to leak through.
- Hold it while it sets Use spring clamps or strips of masking tape every few inches to keep the felt tight against the metal. Check for spots that lift and press them back down within the working time stated on the tube.
- Cure fully before reassembly Leave the clamps in place for the full cure time from the tube instructions. Only then remove the clamps, reinstall the drum, belt and panels, and run an empty air-fluff cycle to confirm the drum turns freely without rubbing.
Fit Checks Before You Call the Job Done
- The felt seal lies flat around its entire circle with no lifted edges or wrinkles.
- The overlap where the felt ends meet is smooth and does not create a high spot.
- No adhesive has squeezed out onto the surface the drum rides on.
- The drum spins by hand without catching or dragging on the seal.
- The drum belt is back on the motor pulley and idler with the grooved side against the drum.
Common Mistakes to Avoid
Gluing over old residue The most common reason a new seal falls off is that it was bonded to old glue instead of bare metal. Take the extra ten minutes with a scraper and abrasive pad.
Using too much adhesive A thick bead never fully hardens near the drum, oozes out under heat and collects lint. One thin, continuous line is all the felt needs.
Rushing the cure Running the dryer while the bond is still soft lets the spinning drum drag the felt right off. Wait the full time the included instructions call for, and longer in a cold garage or basement.
Installing the felt backwards The soft pile must face the drum. If the stiff backing faces the drum you get squealing and rapid wear on the new seal.
Troubleshooting After Installation
Felt seal is loose or peeling after the first few loads The metal was not clean or the cure was cut short. Remove the seal, strip the surface to bare metal again, apply a fresh thin bead and allow the complete cure before running the dryer.
Squealing or scraping noise from the drum The felt is installed pile-inward, is wrinkled, or adhesive squeezed onto the glide surface. Open the cabinet and inspect the seal path with a flashlight while turning the drum by hand.
Small clothing items appear behind the drum There is a gap in the felt, usually at the joint where the ends meet. Add a small overlapping patch of felt bonded with the adhesive to close the gap.
Care Tips After the Repair
- Clean the lint filter every load so debris does not build up along the new seal.
- Avoid overloading; a drum packed with heavy items flexes and wears the seal early.
- Inspect the seal once a year when you vacuum out the cabinet interior.
Compatible Models (Sample)
This part is listed for 1052 Frigidaire models in our fitment data. Always confirm your exact model number on the appliance's rating plate.
Repair Difficulty and Time
Difficulty: Moderate. Typical time: 60 to 90 minutes plus cure time.
Frequently Asked Questions
Can I use regular contact cement instead of 5308027429?
Not for a dryer seal. General-purpose adhesives soften at drum operating temperature and the felt will migrate. This product is made to keep its bond under heat, which is why the manufacturer lists it for felt seals and gaskets.
How long does the adhesive take to cure?
Follow the time printed in the instructions packaged with the tube. Cure time depends on temperature and humidity, so in a cold or damp room give it extra time before you run the dryer.
Which seals in a Frigidaire dryer use this adhesive?
It is typically used for the upper felt drum seal, the lower front duct seal and foam gaskets along the air path. The related part list for this product includes felt seal kits that are designed to be bonded with it.
Final Checklist
- Dryer unplugged and gas valve closed on gas models
- Cabinet opened and drum removed if the rear seal is being replaced
- Old felt and all adhesive residue removed to bare metal
- Surface wiped with alcohol and fully dry
- Thin continuous bead of 5308027429 applied along the seal path
- Felt seated with pile facing the drum and ends overlapped
- Clamped and cured for the full time in the tube instructions