How to Install Glass Crisper WP67006704 in a Whirlpool Refrigerator
Medium Difficulty: What That Means
This job has a medium difficulty rating because the part is fragile and the fit depends on clean support points. The repair does not require advanced tools. It does require control.
You may find the job easier if the old glass is intact. You may need more time if the glass is cracked or stuck to old spills.
Plan for 30 to 60 minutes. The actual glass swap may take less time. Cleaning and safe handling often take the longest.
Use the longer end of that time range when:
- The refrigerator is full.
- Drawers are sticky or hard to remove.
- The old glass has broken.
- The frame needs careful cleaning.
- You need help holding the panel.
Ask another adult to help if the panel feels awkward. A second set of hands can prevent a dropped corner.
Common Mistakes to Avoid
A glass crisper repair can go wrong when you treat it like a normal shelf move. Avoid these mistakes.
Mistake 1: Installing Without Checking the Model
Do not install the part based only on brand and appearance. Whirlpool refrigerators use different shelf designs. Confirm your model number before you start.
Mistake 2: Leaving Debris Under the Glass
A crumb, dried spill, or broken chip can lift one edge. That puts stress on the panel. Clean and dry the frame before seating the replacement.
Mistake 3: Pressing Down on a Raised Corner
If the glass does not sit flat, something is wrong. Pressing down can crack the panel or damage the frame. Lift it out and inspect the ledges.
Mistake 4: Reusing a Broken Support Frame
The glass needs a solid frame. If the plastic support is cracked, the new panel may not be safe to use. Replace or repair the support issue before loading food.
Mistake 5: Loading Heavy Items Too Soon
Test the drawers first. Then reload food in a balanced way. Dropping a heavy container on cold glass can cause damage.
Troubleshooting After Installation
After you install the glass crisper, check how the lower refrigerator section works. A good installation should feel stable and normal.
Use this table to diagnose common problems.
| Problem after installation | Likely cause | What you should do |
|---|---|---|
| Glass rocks in the frame | Debris or misalignment | Remove glass, clean ledges, reseat it |
| Drawer scrapes the glass | Drawer rail or glass position issue | Remove drawer and check alignment |
| One corner sits high | Food chip, warped frame, or wrong seating | Inspect support points before use |
| Glass slides during use | Frame support may not hold it correctly | Stop using shelf and inspect frame |
| Drawer will not close | Drawer loaded wrong or off rail | Empty drawer and reinstall it |
| Crack appears | Impact, stress, or damaged part | Stop using the glass right away |
If the refrigerator still seems not working properly after the shelf area is stable, the glass may not be the cause. Poor cooling, noise, water leaks, or frost buildup can point to a different system. Use Whirlpool’s Service and Support resources when you need official service or manual help.
How This Part Affects Daily Use
The crisper glass helps create a flat shelf over the drawers. It also protects the drawer space from items above. When it sits correctly, the lower fresh food section feels solid.
You may notice these improvements after replacement:
- Drawers open with less rubbing.
- Produce storage feels more stable.
- Containers sit level above the drawers.
- Broken glass is no longer a safety risk.
- Cleaning the crisper area becomes easier.
This repair will not fix every refrigerator issue. It will not repair a compressor, fan, control board, sensor, sealed system, or door gasket. It only addresses the glass crisper panel.
That matters because the symptom list only gives “refrigerator not working properly.” That phrase can mean many things. If the main issue is cracked or unstable crisper glass, WP67006704 may solve the storage problem. If the main issue is warm temperatures, you need more diagnosis.
Quick Decision Matrix
Use this decision matrix before you order or install the glass.
| Your situation | Best next step |
|---|---|
| Your model is AFD2535DEB, AFD2535DES, AFD2535DEW, AFD2535FES, or AFI2538AES | Continue with part verification |
| Your glass is cracked but frame looks solid | Replace the glass and clean the frame |
| Your glass is fine but frame is broken | Identify the frame issue first |
| Your drawer binds after glass removal | Check drawer rails and food blockage |
| Your refrigerator is warm inside | Diagnose cooling before blaming the glass |
| Your model number is different | Verify compatibility before installation |
This table helps you avoid the most expensive mistake: replacing a visible part when the real problem sits elsewhere.
Cleaning Tips While the Glass Is Out
This is a good time to clean the crisper area. You already have the drawers out and the glass removed.
Use warm water and mild dish soap. Clean the drawer rails, frame corners, and front trim. Rinse with a damp cloth. Then dry every contact point.
Do not pour water into the refrigerator. Do not use bleach near food surfaces unless your owner information allows it and you rinse correctly. Avoid strong smells because plastic can hold odors.
Check the drawer tracks while you clean. Food stems, labels, and small packaging pieces can lodge in rails. That debris can make drawers drag even after the glass is replaced.
Let all parts dry before reassembly. Dry plastic and dry glass reduce slipping.
Care After Replacement
New glass still needs smart use. Cold glass is strong when supported correctly, but it can chip from impact.
Follow these care habits:
- Set containers down gently.
- Keep heavy items spread out.
- Do not slam drawers.
- Clean spills before they harden.
- Avoid twisting the panel during cleaning.
- Remove the glass with two hands when needed.
If you wash the glass outside the refrigerator, let it warm slightly first. Sudden temperature changes can stress glass. Use warm water, not very hot water.
Do not place the glass in a dishwasher unless your official refrigerator information says that is allowed. When in doubt, hand clean it.
When to Stop and Get Help
You should stop the repair if the job no longer matches a glass replacement. That keeps you from wasting time or breaking another part.
Stop when:
- The frame is cracked.
- The drawer rails are broken.
- The new glass does not match the opening.
- The model number does not match your supplied list.
- You find wiring damage.
- You see heavy frost behind panels.
- The refrigerator has cooling problems unrelated to the shelf.
A glass crisper replacement should be controlled and direct. It should not require force, cutting, drilling, or bending plastic. If you reach that point, something is off.
Internal Repair Resources
You may also want to review related refrigerator repair topics before you replace more parts:
- Refrigerator drawer and shelf repair guide
- Refrigerator not cooling troubleshooting
- How to clean refrigerator parts safely
Use these guides to separate storage issues from cooling issues. That step matters when the symptom is broad.
What to Do Next
Need help finding the right part for your Whirlpool refrigerator?
Final Installation Checklist
Use this checklist before you close the job.
- You confirmed the refrigerator is a Whirlpool model.
- You confirmed the OEM number WP67006704.
- You checked that your model is in the supplied compatible list.
- You removed food from the crisper area.
- You handled old glass with both hands.
- You cleaned and dried the support frame.
- You checked the frame for cracks or damage.
- You placed the replacement glass flat in the frame.
- You tested both crisper drawers.
- You reloaded food without dropping heavy items.
- You closed the door and checked for blocked storage.
If every item checks out, the glass crisper installation is complete.