How to Install Grommet 134371300 in a Frigidaire Washer
Before You Start
Installing a washer grommet is a medium-difficulty repair. Plan on 30 to 60 minutes if the washer is easy to reach. It can take longer if the unit sits in a tight laundry closet.
You should work slowly and keep every screw in order. Many washer panels use similar screws, but similar does not mean the same. Mixing them up can cause poor panel fit or stripped holes.
This repair is not about force. A grommet should sit flat and secure once the area is clean and aligned. If you have to crush it, stretch it hard, or pry nearby parts out of shape, stop and check the fit.
Use this repair when the old grommet shows wear, hardening, cracking, looseness, or poor seating. You may also need it if a nearby hose, wire, bracket, or panel opening no longer feels protected.
Models Listed for This Grommet
The provided compatible Frigidaire washer models are:
- ATF6000FS1
- ATF6700FS1
- ATF8000FS1
- EIFLS55IIW0
- EIFLS55IMB0
Check your washer’s model tag before starting. On many front-load washers, the model tag may be near the door opening or behind the door area. If you cannot find it, check your owner paperwork.
Match the full model number. Do not stop at the first few letters or numbers. A washer series can have several versions, and small differences can matter.
What the Grommet Does
A washer grommet protects an opening, contact point, or pass-through area. It may cushion vibration, reduce rubbing, protect a line, or help hold a part in place. The exact location can vary by washer design, so use your model layout and the old part location as your guide.
Think of the grommet as a small shield. It keeps harder parts from wearing into softer parts. It also helps reduce movement where the washer shakes during wash and spin cycles.
When a grommet fails, you may not see a clear error code or dramatic breakdown. You may only notice that the washer is not working properly. You may also see rubbing marks, loose routing, odd vibration, or a part that no longer sits where it should.
Signs the Old Grommet May Be Bad
Look for these signs before you remove parts:
- The grommet looks cracked or split.
- Rubber feels hard, brittle, or flattened.
- The part no longer grips its opening.
- A nearby line, wire, or panel edge shows rub marks.
- The washer has more vibration than usual.
- A protected part has shifted out of place.
- The washer is not working properly after other causes were checked.
Do not blame the grommet for every washer problem. A washer can act up for many reasons. Still, a damaged grommet should not stay in service once you find it.
Tools and Supplies
Use common hand tools unless your washer setup needs something different.
You may need:
- Phillips screwdriver
- Flathead screwdriver
- Nut driver or socket set
- Work gloves
- Towels
- Small container for screws
- Flashlight
- Mild cleaner
- Soft cloth
Do not use sharp tools against rubber unless you must remove a destroyed old part. A sharp blade can nick a hose, wire, or plastic edge.
Safety First
Unplug the washer before you open any panel. Water and electricity do not mix. You should also turn off the water supply valves if you will move the washer or work near water lines.
Pull the washer forward only if you can do it safely. Get help if the floor is slick or the unit is stacked. Do not lean the washer at a sharp angle unless the service steps for your exact model call for it.
Keep towels nearby. Even a small amount of trapped water can spill when you move parts. Protect the floor before you begin.
If you see burned wiring, melted plastic, a damaged harness, or heavy water damage, stop. Those problems need more diagnosis before you install a grommet.
Quick Decision Table
Use this table before you begin. It helps you decide if this repair makes sense today.
| What You See | What It Usually Means | Best Next Step |
|---|---|---|
| Grommet is cracked or split | Rubber has failed | Replace the grommet |
| Grommet is loose in the opening | It may no longer grip | Replace and inspect the opening |
| Nearby part has rub marks | Protection may be gone | Replace grommet and check alignment |
| Grommet looks fine | Problem may be elsewhere | Keep diagnosing the washer |
| Washer has major leaks | More than a grommet may be involved | Check hoses, seals, and fittings |
| Wiring looks damaged | Safety risk | Stop and inspect before use |
A grommet repair works best when the old part shows clear wear. If you cannot find damage, do not force the repair as the only answer.
How to Install Grommet 134371300
Common Mistakes to Avoid
Many grommet repairs fail because of small errors. Avoid these mistakes.
Installing It Backward
Some grommets have a shaped lip or side profile. If you install it backward, it may not grip well. Use the old part and your photo as guides.
Leaving Dirt in the Seat
Soap film and grit can stop rubber from sitting flat. Clean the area before you press in the new part.
Forcing a Poor Fit
A correct grommet should need steady pressure, not heavy force. If it feels wrong, stop and recheck the model and part.
Pinching Nearby Parts
A hose or wire can get trapped under a panel during reassembly. Always check routing before you tighten the last screws.
Skipping the Test Cycle
Do not push the washer back and call it done right away. Run a short test first. A test helps you catch leaks, rubbing, or loose panels.
What If the Washer Still Does Not Work Properly?
A new grommet fixes only the problem caused by that grommet. If the washer still acts up, keep looking.
Check for these common areas:
- Door latch operation
- Drain hose position
- Water supply valves
- Inlet hose condition
- Drain pump area
- Load balance
- Control settings
- Visible leaks
- Loose panels
- Worn hoses or clamps
Do not replace random parts. That gets expensive and wastes time. Use what you see, hear, and test.
If the washer fills but will not drain, focus on the drain path. If it shakes hard, check leveling and load balance. If it will not start, check power, door closure, and controls.
Fit Check for Frigidaire Washer Grommet 134371300
A proper fit should look clean and stable. Use this checklist after installation:
- The grommet sits flat.
- The lip is not folded.
- No nearby part is pinched.
- No wire or hose rubs a sharp edge.
- The panel fits back in place.
- The washer does not make a new rubbing sound.
- The serviced area stays dry during testing.
If one item fails, fix it before regular use. A small installation issue can become a larger repair later.
Why Small Rubber Parts Matter
Small washer parts often do quiet work. A grommet may not control the wash cycle, but it can protect parts that matter. Once rubber fails, movement and vibration can spread wear to other areas.
Washers shake by design. During spin, the tub moves, the cabinet reacts, and nearby parts deal with constant motion. Rubber parts help manage that motion.
A missing or damaged grommet can let parts touch in ways they should not. Over time, that contact can cause noise, wear, leaks, or electrical risk if wiring becomes damaged.
Replacing the grommet early can prevent more damage. It is a modest repair with real value when the old part has failed.
Installation Difficulty and Time
This repair has a medium difficulty level. Most of the challenge comes from access, not the grommet itself.
Plan for 30 to 60 minutes. Add time if you must move the washer, remove tight panels, or clean heavy buildup.
You should be comfortable using hand tools. You should also be patient with rubber seating. If you rush, the grommet may twist or sit unevenly.
Stop if you reach a point that feels unsafe. A washer is heavy, and some areas can have sharp metal edges.
Maintenance Tips After Replacement
After you install the new grommet, keep the washer area clean and dry. Moisture, detergent residue, and vibration can all shorten the life of rubber parts.
Use these habits:
- Wipe visible moisture after leaks or spills.
- Keep the washer level.
- Avoid overloading the drum.
- Use the right amount of detergent.
- Check hoses during routine cleaning.
- Listen for new rubbing sounds.
- Inspect rubber parts if the washer starts vibrating more.
You do not need to take the washer apart every month. Just pay attention when something changes. New sounds often give you an early warning.
When to Call for Help
Call for help if you find damaged wiring, heavy leaking, broken mounting points, or signs of overheating. Those problems go beyond a basic grommet install.
You should also get help if the washer is stacked, boxed into a tight space, or too heavy to move safely. Saving a service fee is not worth an injury.
If you are unsure about part fit, use the washer model number and part number before ordering. A few minutes of checking can prevent a wrong repair.
What to Do Next
Need help finding the right part for your Frigidaire washer?
Final Repair Checklist
Before you finish, check each item:
- You unplugged the washer before service.
- You matched the full washer model number.
- You removed only the panels needed for access.
- You cleaned the grommet seat.
- You installed Grommet 134371300 without twisting it.
- You checked nearby hoses, wires, or parts.
- You reinstalled all panels correctly.
- You restored water and power.
- You ran a short test cycle.
- You checked for leaks, rubbing, and vibration.
If every item passes, you can return the washer to normal use.