How to Install Filter Support 67006325 in a Whirlpool Refrigerator
Step 1: Power Down and Protect the Area
Move food away from the work zone. If the filter sits inside the fresh food section, remove nearby items so they do not fall or block your hands.
Unplug the refrigerator. Do not rely on turning off a control panel. You want the unit disconnected from power before you work.
Shut off the water supply valve. The valve may be behind the refrigerator, under the sink, or in the basement. Turn it off fully, then place a towel near the filter area.
Remove the water filter if it blocks the support. Some filters twist out. Others push or pull out. Use the normal removal method for your refrigerator. Do not force it.
If the filter will not release, stop and inspect the support. A broken support may be binding the filter.
Step 2: Open Access to the Filter Support
Look for covers, trim pieces, or shelves that block the filter support. Remove only what you need for clear access.
Use a flashlight to spot screws and tabs. Refrigerator interiors often hide fasteners under caps or behind trim edges.
Take photos before you remove anything. A clear before-photo helps when you route parts back into place.
Keep one hand on plastic trim while loosening screws. That prevents parts from dropping or twisting.
If a cover resists removal, do not pry hard. Check for another screw or clip. Plastic tabs can break fast when you pry from the wrong side.
The goal is controlled access, not full disassembly. Remove the fewest parts needed to reach the support.
Step 3: Remove the Old Filter Support
Study the old support before you remove it. Note how it sits, where it locks, and how the filter lines up with it.
Loosen the mounting screws by hand. If tabs hold the support, press them gently with a small flat blade screwdriver. Keep pressure light.
Pull the old support out slowly. Watch for attached pieces or water line contact points. Do not yank the part free.
If the support is cracked, it may come out in pieces. Remove all broken bits before installing the new part. Small plastic pieces can block the replacement from sitting flat.
Check the mounting area for damage. If the refrigerator liner or housing is broken, a new support may not solve the full problem.
Clean the area with a dry towel. Do not flood the opening with water or cleaner.
Step 4: Install the New Support
Place Filter Support 67006325 in the same orientation as the old support. Use your photo if you feel unsure.
Line up tabs first. Then line up screw holes. Plastic parts should sit naturally when aligned. They should not need heavy pressure.
Start each screw by hand before tightening any screw fully. This keeps the support from shifting while you work.
Tighten the screws until snug. Stop when the support feels secure. Over-tightening can crack plastic or strip the mounting point.
If tabs lock the support, press until they seat. You may feel or hear a soft snap. Do not hit the part with a tool.
Reinstall the filter. It should seat with a firm, even feel. If it tilts, binds, or pops out, remove it and inspect the support alignment again.
Step 5: Restore Water and Test
Reinstall any cover, trim, shelf, or bin you removed. Make sure nothing presses against the filter.
Turn the water supply back on slowly. Watch the filter area while pressure returns.
Plug the refrigerator back in. Let the controls restart.
If your refrigerator has a water dispenser, run water and keep watching the filter area. Some air may move through the line after service. That can cause short bursts or sputtering.
Look for leaks around the filter and support. Check again after 10 minutes. Then check once more later the same day.
A dry filter area is the goal. If you see water, shut off the supply and inspect the filter seat.
Mistakes That Can Damage the Repair
Small errors can turn this medium repair into a bigger job. Avoid these common problems.
| Pitfall | Why It Matters | Better Move |
|---|---|---|
| Forcing the water filter | It can crack the new support | Remove and realign the filter |
| Over-tightening screws | Plastic mounts can strip or split | Tighten by hand until snug |
| Skipping photos | Reassembly becomes guesswork | Photograph each stage |
| Ignoring a leak | Water can damage nearby parts | Shut off water and inspect |
| Mixing screws | Wrong screws may not hold right | Keep screws grouped in order |
| Prying hard on trim | Hidden tabs can break | Find the release point first |
The biggest mistake is force. Refrigerator filter parts should feel firm, not violent. If the part fights you, something is misaligned.
Repair Decision Matrix
Use this quick matrix before you commit to the repair.
| What You See | Likely Direction |
|---|---|
| Filter support is cracked | Replace the support |
| Filter feels loose but support looks intact | Check filter seating and support alignment |
| Water leaks only after filter change | Inspect filter, support, and seal area |
| Filter will not lock in | Check for broken tabs or wrong filter position |
| Refrigerator issue has no link to filter area | Troubleshoot other systems first |
This matrix does not replace diagnosis. It helps you slow down and avoid changing the wrong part.
If the refrigerator is not cooling, making strange compressor sounds, or showing control issues, the filter support may not be the cause. Focus on symptoms near the filter area.
When to Stop and Get Help
Stop the repair if you see damaged water lines, broken housing sections, or wiring near the work area. Those problems need a higher level of care.
Also stop if the filter support does not match the old part. Do not modify the part to make it fit.
Get help if the water will not shut off fully. You should not work on the filter area with active water pressure.
You should also pause if the filter remains loose after the new support is installed. That may point to another damaged part in the filter system.
For model-specific help, Whirlpool’s Product Help Library can help you review refrigerator support topics.
Internal Checks After Installation
Once the repair is complete, check the refrigerator over the next day.
Start with the filter area. It should stay dry. The filter should stay locked in place. The support should not shift when you touch the filter.
Next, check water flow if your refrigerator has a dispenser. Flow should be steady after trapped air clears.
Then inspect nearby shelves and bins. Make sure nothing blocks the filter or presses against the support.
Listen for unusual sounds. A filter support repair should not create new noises. If you hear a new rattle near the filter area, inspect the cover or trim.
Finally, check the floor near the refrigerator. Water can travel before it appears. A dry floor gives you more confidence that the repair sealed correctly.
Maintenance Tips for the Filter Area
Handle the filter area gently during future filter changes. Most support damage starts with force.
Use straight pressure when installing the filter. Keep it aligned with the opening. Do not twist at an angle.
Replace filters according to your refrigerator needs and water use. When you remove a filter, support it with your hand and follow the normal release method.
Wipe the filter compartment during routine cleaning. Dust and residue can make parts harder to inspect.
Check the support whenever you change the filter. Look for cracks, loose screws, or tabs that no longer hold.
Keep the model number recorded somewhere safe. A photo of the model tag saves time when you need future parts.
What to Do Next
Need help finding the right part for your Whirlpool refrigerator?
Final Checklist
Before you call the job done, confirm each item below.
- You unplugged the refrigerator before service.
- You shut off the water supply before opening the filter area.
- You confirmed the replacement part number is 67006325.
- You checked your refrigerator model number.
- You removed covers and trim without breaking tabs.
- You installed the support square and snug.
- You reinstalled the filter with a firm seat.
- You turned the water back on slowly.
- You checked for leaks right away.
- You checked again later the same day.
A good repair should feel stable. The filter should not wobble, bind, or drip. If it does, reopen the area and inspect the alignment.