Parts for DDP1380TAM — GE Dryer

We found 17 parts confirmed to fit the GE Dryer DDP1380TAM.

Compatibility table

Prices shown are an informational reference range only, not an offer or an Amazon price — RepairKitHub does not sell parts directly. Each part links to an Amazon search so you can compare current listings yourself.

Common failure areas on this model

The confirmed parts above group into a handful of failure areas. Here is what each points to and how to check it before you order anything.

General hardware and mounting parts

Symptom: A small mechanical or mounting part has failed, cracked, or gone missing.

Check: Compare the physical shape and mounting points to the original piece, and confirm the exact part number against your model plate before ordering.

Parts in this group on DDP1380TAM: 311819 (Installation), WE1X1088 (Knockout), WE1M317 (Retainer), WE1M404 (Slide), WE1M356 (We1m353), WE1M407 (Lint Grid Slide), WE1M314 (Strike), WE1M406 (Grid), WE3M15 (Bearing Kit), WE4X710 (Motor), WE2X195 (Washer).

Door and drum seals

Symptom: A drum seal that's worn through, letting the dryer pull in room air instead of pushing heated air through the load.

Check: Look for the drum seal fraying or missing where it meets the front or rear bulkhead -- worn felt or foam here is visible once the front panel is off.

Parts in this group on DDP1380TAM: WE9M16 (Dryer Door Seal).

Storage, trim and cosmetic hardware

Symptom: A cracked shelf, broken door bin, worn hinge, or missing trim piece -- cosmetic and storage wear rather than a functional breakdown.

Check: Match the physical dimensions and mounting tabs of the old part before ordering; these pieces are often model-specific even between visually similar models.

Parts in this group on DDP1380TAM: WE11M24 (Heater Housing), WE10M86 (Outer Door Panel), WE1X1032 (Latch Clip), WE2M96 (Cap Nut).

Heat control (thermostats, fuses, heating element)

Symptom: The dryer runs but produces no heat, or it shuts off partway through the cycle.

Check: With the dryer unplugged, check continuity across the part with a multimeter -- no continuity means it has failed. Clear the lint vent first, since a blocked vent is what usually trips a thermal fuse in the first place.

Parts in this group on DDP1380TAM: WE4M160 (Dryer Safety Thermostat).

Before you buy

Match DDP1380TAM exactly against the model and serial plate on the appliance itself before ordering anything — a single mismatched character can point to a different production run with different parts. Then check the part number printed or stamped on the part you are replacing against the part numbers in the table above; the printed number is the most reliable way to confirm fitment when a model has gone through multiple production runs. RepairKitHub does not sell parts directly — every part link above routes to an Amazon search for that part number so you can compare current listings and sellers yourself.

How to confirm this is your model

On most dryers, the model and serial plate sits inside the door opening or behind the lint trap. Match every character exactly, including letters and dashes at the end — appliance model numbers often have similar prefixes but different suffixes for different production runs.

Neighbouring GE Dryer models

These model numbers sort next to this one in the catalog and are usually the same product family.

• DDSR475ET0AA — 10 parts
• DDSR475ET0WW — 10 parts
• DDSR475ET2AA — 10 parts
• DDSR475ET2WW — 10 parts
• DDSR475ET3AA — 10 parts
• DDP1380SDM — 18 parts
• DDP1380SCM — 17 parts
• DDP1380SBM — 18 parts
• DDP1380SAM — 12 parts
• DDP1380GFM — 18 parts

Still not sure?

Use the model lookup tool to search by model or part number, or start from the symptom your appliance is showing.