Parts for DDP1380SCM — GE Dryer

We found 17 parts confirmed to fit the GE Dryer DDP1380SCM.

Compatibility table

All 17 confirmed parts, ordered so parts that fit fewer models (more specific to this appliance) appear first.
Part #PartAlso fitsReference price
311819Installation9 models$7.03 · Amazon
WE9M16Dryer Door Seal10 models$93.40 · Amazon
WE11M24Heater Housing10 models$96.11 · Amazon
WE10M86Outer Door Panel10 models$103.58 · Amazon
WE4M154Resistor10 models$29.99 · Amazon
WE1M317Retainer10 models$30.53 · Amazon
WE1M356We1m35310 models$23.73 · Amazon
WE12X79Belt17 models$119.56 · Amazon
WE1M314Strike24 models$7.49 · Amazon
WE2M98Screw28 models$58.83 · Amazon
WE1M280Screw102 models$10.47 · Amazon
WE3X65Sleeve Bearing150 models$72.81 · Amazon
WE4M160Dryer Safety Thermostat239 models$179.92 · Amazon
WE4X710Motor312 models$159.99 · Amazon
WE2X195Washer539 models$72.81 · Amazon
WE1X1032Latch Clip590 models$13.61 · Amazon
WE1X688Dryer Blower Wheel Retainer Assembly665 models$22.02 · Amazon

Prices shown are an informational reference range only, not an offer or an Amazon price — RepairKitHub does not sell parts directly. Each part links to an Amazon search so you can compare current listings yourself.

Common failure areas on this model

The confirmed parts above group into a handful of failure areas. Here is what each points to and how to check it before you order anything.

General hardware and mounting parts

Symptom: A small mechanical or mounting part has failed, cracked, or gone missing.

Check: Compare the physical shape and mounting points to the original piece, and confirm the exact part number against your model plate before ordering.

Parts in this group on DDP1380SCM: 311819 (Installation), WE4M154 (Resistor), WE1M317 (Retainer), WE1M356 (We1m353), WE1M314 (Strike), WE3X65 (Sleeve Bearing), WE4X710 (Motor), WE2X195 (Washer).

Door and drum seals

Symptom: A drum seal that's worn through, letting the dryer pull in room air instead of pushing heated air through the load.

Check: Look for the drum seal fraying or missing where it meets the front or rear bulkhead -- worn felt or foam here is visible once the front panel is off.

Parts in this group on DDP1380SCM: WE9M16 (Dryer Door Seal).

Storage, trim and cosmetic hardware

Symptom: A cracked shelf, broken door bin, worn hinge, or missing trim piece -- cosmetic and storage wear rather than a functional breakdown.

Check: Match the physical dimensions and mounting tabs of the old part before ordering; these pieces are often model-specific even between visually similar models.

Parts in this group on DDP1380SCM: WE11M24 (Heater Housing), WE10M86 (Outer Door Panel), WE2M98 (Screw), WE1M280 (Screw), WE1X1032 (Latch Clip).

Drive system (belts, pulleys, motors)

Symptom: A drum or tub that won't turn, a burning-rubber smell, or a loud thump or squeal during a cycle.

Check: With power off, turn the drum or tub by hand -- resistance or grinding points to the motor or a bearing, and a cracked, glazed, or snapped belt is visible once the cabinet is open.

Parts in this group on DDP1380SCM: WE12X79 (Belt).

Heat control (thermostats, fuses, heating element)

Symptom: The dryer runs but produces no heat, or it shuts off partway through the cycle.

Check: With the dryer unplugged, check continuity across the part with a multimeter -- no continuity means it has failed. Clear the lint vent first, since a blocked vent is what usually trips a thermal fuse in the first place.

Parts in this group on DDP1380SCM: WE4M160 (Dryer Safety Thermostat).

Venting and airflow

Symptom: A dryer that needs multiple cycles to dry, runs unusually hot, or repeatedly trips its heat-limit switch.

Check: Clear the lint screen and the full vent run to the outside wall -- a restricted vent is the single most common cause of long dry times and repeat thermal-fuse failures.

Parts in this group on DDP1380SCM: WE1X688 (Dryer Blower Wheel Retainer Assembly).

Before you buy

Match DDP1380SCM exactly against the model and serial plate on the appliance itself before ordering anything — a single mismatched character can point to a different production run with different parts. Then check the part number printed or stamped on the part you are replacing against the part numbers in the table above; the printed number is the most reliable way to confirm fitment when a model has gone through multiple production runs. RepairKitHub does not sell parts directly — every part link above routes to an Amazon search for that part number so you can compare current listings and sellers yourself.

How to confirm this is your model

On most dryers, the model and serial plate sits inside the door opening or behind the lint trap. Match every character exactly, including letters and dashes at the end — appliance model numbers often have similar prefixes but different suffixes for different production runs.

Neighbouring GE Dryer models

These model numbers sort next to this one in the catalog and are usually the same product family.

Still not sure?

Use the model lookup tool to search by model or part number, or start from the symptom your appliance is showing.