Parts for WSM2780HDWWW — GE

We found 70 parts confirmed to fit the GE WSM2780HDWWW.

Compatibility table

Prices shown are an informational reference range only, not an offer or an Amazon price — RepairKitHub does not sell parts directly. Each part links to an Amazon search so you can compare current listings yourself.

Common failure areas on this model

The confirmed parts above group into a handful of failure areas. Here is what each points to and how to check it before you order anything.

Controls, timers and wiring

Symptom: A cycle that doesn't advance, an unresponsive display, or the unit not starting at all.

Check: Look for burn marks or a burnt smell near the board or terminals, and check whether buttons and knobs respond -- a unit that powers on but won't cycle often traces back to this group.

Parts in this group on WSM2780HDWWW: WE08X10073 (Wiring Harness), WH12X10425 (Capacitor), WH08X10033 (Wiring Harness), WE08X10072 (Laundry Center Wire Harness), WH11X10019 (Laundry Center Washer Timer Dial (White)), WH12X10083 (Washer Water-Level Pressure Switch), WE04X10005 (Dryer Timer), WH12X10164 (Laundry Center Washer Timer).

Storage, trim and cosmetic hardware

Symptom: A cracked shelf, broken door bin, worn hinge, or missing trim piece -- cosmetic and storage wear rather than a functional breakdown.

Check: Match the physical dimensions and mounting tabs of the old part before ordering; these pieces are often model-specific even between visually similar models.

Parts in this group on WSM2780HDWWW: WE20X10093 (Panel White), WH01X10454 (Spring Assis), WE01X10215 (Heat Shield), WE14X10081 (Heater Housing), WE02X10071 (Screw), WE14X10024 (Burner Tube), WE01X10050 (Dryer Door Handle), WE14X10083 (Laundry Center Dryer Blower Housing), WE13X10029 (Panel Motor), WE20X744 (Cover T Bl), WE13X10009 (Dryer Drum Bearing Bracket), WE02X10067 (Hex Washer Head Screw), WJ45X10027 (Tub Cover), WH2X1150 (Screw).

General hardware and mounting parts

Symptom: A small mechanical or mounting part has failed, cracked, or gone missing.

Check: Compare the physical shape and mounting points to the original piece, and confirm the exact part number against your model plate before ordering.

Parts in this group on WSM2780HDWWW: WE04X10132 (Dryer Igniter), WH01X10344 (Laundry Center Washer Lid Strike Plate), WE01X10175 (Gas Pipe), WH01X10013 (Locating Pin), WH16X502 (Brkt Joine), WE1X1152 (Dryer Drum Grounding Ball), WE01X10248 (Gas Pipe), WE21X69 (Laundry Center Dryer Drum Baffle), WH01X10048 (Laundry Center Washer Hose Clamp), WH12X10036 (Laundry Center Washer Water Temperature Switch), WE1X1262 (Plug), WH1X2312 (Snubber Ring), WE01X10007 (Valve Gas Sh), WE9X104 (Washer Seal), WE09X10014 (Dryer Drum Felt Seal, Lower), WH4X104 (Laundry Center Washer Spin Bearing), WE01X10247 (Pipe), WH41X10038 (Pressure Tub), WH02X10031 (Pump Clamp), WH01X10063 (Ring Drain H), WE02X10058 (Union,hex Nu), WH2X1133 (Washer), WE14X206 (Elbow), WE10X10004 (Inner Door), WE14X207 (Laundry Center Dryer Gas Valve), WE14X10068 (Burner Assembly), WH01X10101 (Hex Nut), WH01X10042 (Locating Pin), WH44X1137 (Laundry Center Washer Lid), WE4X744 (Resistor), WH41X10099 (Inlet Hose).

Door, lid switches and latches

Symptom: The appliance won't start, or stops, unless the lid or door is fully latched shut.

Check: Listen for an audible click when the lid or door closes. No click, or a visibly cracked plastic tab on the latch, points to this part.

Parts in this group on WSM2780HDWWW: WE08X10074 (Laundry Center Dryer Door Switch Harness).

Water inlet and drainage

Symptom: The unit isn't getting water when it should, or isn't draining or pumping it out when it should.

Check: Check the valve or pump for a clog or jammed object, and confirm the hose isn't kinked, restricted, or routed higher than the unit allows.

Parts in this group on WSM2780HDWWW: WH13X10035 (Washer Water Inlet Valve Assembly), WH01X10189 (Washer Drain Hose), WH41X10027 (Washer Tub-to-Pump Hose).

Drive system (belts, pulleys, motors)

Symptom: A drum or tub that won't turn, a burning-rubber smell, or a loud thump or squeal during a cycle.

Check: With power off, turn the drum or tub by hand -- resistance or grinding points to the motor or a bearing, and a cracked, glazed, or snapped belt is visible once the cabinet is open.

Parts in this group on WSM2780HDWWW: WE1X1159 (Dryer Idler Spring), WH7X115 (Washer Idler Pulley).

Heat control (thermostats, fuses, heating element)

Symptom: The appliance runs but heats or cools inconsistently, or shuts off partway through a cycle.

Check: With the appliance unplugged, check continuity across the part with a multimeter -- no continuity means it has failed.

Parts in this group on WSM2780HDWWW: WE04X10040 (Laundry Center Dryer Safety Thermostat).

Before you buy

Match WSM2780HDWWW exactly against the model and serial plate on the appliance itself before ordering anything — a single mismatched character can point to a different production run with different parts. Then check the part number printed or stamped on the part you are replacing against the part numbers in the table above; the printed number is the most reliable way to confirm fitment when a model has gone through multiple production runs. RepairKitHub does not sell parts directly — every part link above routes to an Amazon search for that part number so you can compare current listings and sellers yourself.

How to confirm this is your model

Check inside a door opening, on a back or side panel, or behind a removable panel or drawer for a label printed with the model and serial number. Match every character exactly, including letters and dashes at the end — appliance model numbers often have similar prefixes but different suffixes for different production runs.

Still not sure?

Use the model lookup tool to search by model or part number, or start from the symptom your appliance is showing.