Parts for GTUP270EM5WW — GE Dryer
We found 10 parts confirmed to fit the GE Dryer GTUP270EM5WW.
Compatibility table
| Part # | Part | Also fits | Reference price |
|---|---|---|---|
| WH13X10064 | Washer Water Inlet Valve | 35 models | — |
| WE4M521 | Laundry Center Control Timer | 62 models | — |
| WE1M1068 | Laundry Center Dryer Door Handle WE1M1068 | 69 models | $69.47 |
| WH23X10040 | Washer Drain Pump | 75 models | — |
| WE16X20393 | Laundry Center Dryer Blower Wheel | 253 models | — |
| WE3M52 | Dryer Drum Glide Bearing, Upper | 381 models | — |
| WE4M416 | Dryer Push-to-Start Switch | 411 models | — |
| WE3M51 | Dryer Drum Glide Bearing | 415 models | — |
| WE12M29 | Dryer Drum Belt | 1,147 models | — |
| WE4M137 | Dryer High-Limit Thermostat | 1,547 models | — |
Prices shown are an informational reference range only, not an offer or an Amazon price — RepairKitHub does not sell parts directly. Each part links to an Amazon search so you can compare current listings yourself.
Common failure areas on this model
The confirmed parts above group into a handful of failure areas. Here is what each points to and how to check it before you order anything.
Water inlet and drainage
Symptom: The unit isn't getting water when it should, or isn't draining or pumping it out when it should.
Check: Check the valve or pump for a clog or jammed object, and confirm the hose isn't kinked, restricted, or routed higher than the unit allows.
Parts in this group on GTUP270EM5WW: WH13X10064 (Washer Water Inlet Valve), WH23X10040 (Washer Drain Pump).
Controls, timers and wiring
Symptom: A cycle that doesn't advance, an unresponsive display, or the dryer not starting at all.
Check: Look for burn marks or a burnt smell near the board or terminals, and check whether buttons and knobs respond -- a unit that powers on but won't cycle often traces back to this group.
Parts in this group on GTUP270EM5WW: WE4M521 (Laundry Center Control Timer).
Storage, trim and cosmetic hardware
Symptom: A cracked shelf, broken door bin, worn hinge, or missing trim piece -- cosmetic and storage wear rather than a functional breakdown.
Check: Match the physical dimensions and mounting tabs of the old part before ordering; these pieces are often model-specific even between visually similar models.
Parts in this group on GTUP270EM5WW: WE1M1068 (Laundry Center Dryer Door Handle WE1M1068).
Venting and airflow
Symptom: A dryer that needs multiple cycles to dry, runs unusually hot, or repeatedly trips its heat-limit switch.
Check: Clear the lint screen and the full vent run to the outside wall -- a restricted vent is the single most common cause of long dry times and repeat thermal-fuse failures.
Parts in this group on GTUP270EM5WW: WE16X20393 (Laundry Center Dryer Blower Wheel).
General hardware and mounting parts
Symptom: A small mechanical or mounting part has failed, cracked, or gone missing.
Check: Compare the physical shape and mounting points to the original piece, and confirm the exact part number against your model plate before ordering.
Parts in this group on GTUP270EM5WW: WE3M52 (Dryer Drum Glide Bearing, Upper), WE4M416 (Dryer Push-to-Start Switch), WE3M51 (Dryer Drum Glide Bearing).
Drive system (belts, pulleys, motors)
Symptom: A drum or tub that won't turn, a burning-rubber smell, or a loud thump or squeal during a cycle.
Check: With power off, turn the drum or tub by hand -- resistance or grinding points to the motor or a bearing, and a cracked, glazed, or snapped belt is visible once the cabinet is open.
Parts in this group on GTUP270EM5WW: WE12M29 (Dryer Drum Belt).
Heat control (thermostats, fuses, heating element)
Symptom: The dryer runs but produces no heat, or it shuts off partway through the cycle.
Check: With the dryer unplugged, check continuity across the part with a multimeter -- no continuity means it has failed. Clear the lint vent first, since a blocked vent is what usually trips a thermal fuse in the first place.
Parts in this group on GTUP270EM5WW: WE4M137 (Dryer High-Limit Thermostat).
Before you buy
Match GTUP270EM5WW exactly against the model and serial plate on the appliance itself before ordering anything — a single mismatched character can point to a different production run with different parts. Then check the part number printed or stamped on the part you are replacing against the part numbers in the table above; the printed number is the most reliable way to confirm fitment when a model has gone through multiple production runs. RepairKitHub does not sell parts directly — every part link above routes to an Amazon search for that part number so you can compare current listings and sellers yourself.
How to confirm this is your model
On most dryers, the model and serial plate sits inside the door opening or behind the lint trap. Match every character exactly, including letters and dashes at the end — appliance model numbers often have similar prefixes but different suffixes for different production runs.
Neighbouring GE Dryer models
These model numbers sort next to this one in the catalog and are usually the same product family.
Still not sure?
Use the model lookup tool to search by model or part number, or start from the symptom your appliance is showing.