Parts for A212 — Whirlpool Washer

We found 19 parts confirmed to fit the Whirlpool Washer A212.

Compatibility table

All 19 confirmed parts, ordered so parts that fit fewer models (more specific to this appliance) appear first.
Part #PartAlso fitsReference price
W10175938BOLT30 models$9.62
WP22003410Corrugated Drain Hose30 models$50.56
WP211948Drive Belt - 120v 50 cycle30 models$84.23
WPW10221114Gear Pinion30 models$52.67
WPY215234Injector Fill Hose30 models$42.12
12002352MOTOR-DRVE30 models$256.38
205134Motor Switch30 models$67.51
WPY206629PIN- COLLA30 models$9.62
WP211451Pump Belt30 models$72.00
WP22001448Pump-to-Siphon Break Drain Hose30 models$63.64
WPY313561SCREW----NA (PART NOT USED-DE30 models$7.47
206638Siphon Break Connector Kit30 models$51.61
208847Syphon Break Elbow Kit with Clamp30 models$32.63
WP214765Syphon Break Gasket30 models$53.20
WP206680Washer Injector Hose w/Air Gap30 models$77.22
WP311155Wire30 models$12.85
WP215581Agitator Shaft Spring76 models$6.50–$9.62
WP215447Washer Injector Sleeve77 models$6.40–$9.62
202860Inlet Hose Kit423 models$57.26

Prices shown are an informational reference range only, not an offer or an Amazon price — RepairKitHub does not sell parts directly. Each part links to an Amazon search so you can compare current listings yourself.

Common failure areas on this model

The confirmed parts above group into a handful of failure areas. Here is what each points to and how to check it before you order anything.

General hardware and mounting parts

Symptom: A small mechanical or mounting part has failed, cracked, or gone missing.

Check: Compare the physical shape and mounting points to the original piece, and confirm the exact part number against your model plate before ordering.

Parts in this group on A212: W10175938 (BOLT), WPW10221114 (Gear Pinion), 12002352 (MOTOR-DRVE), 205134 (Motor Switch), WPY206629 (PIN- COLLA), 208847 (Syphon Break Elbow Kit with Clamp), WP206680 (Washer Injector Hose w/Air Gap), WP311155 (Wire), WP215447 (Washer Injector Sleeve), 202860 (Inlet Hose Kit).

Water inlet and drainage

Symptom: A washer that won't fill, fills slowly, won't drain, or leaves standing water in the tub.

Check: For fill problems, check the inlet valve's screen filters for sediment. For drain problems, check the pump for a jammed object and confirm the drain hose isn't kinked or looped too high.

Parts in this group on A212: WP22003410 (Corrugated Drain Hose), WPY215234 (Injector Fill Hose), WP22001448 (Pump-to-Siphon Break Drain Hose), 206638 (Siphon Break Connector Kit).

Drive system (belts, pulleys, motors)

Symptom: A drum or tub that won't turn, a burning-rubber smell, or a loud thump or squeal during a cycle.

Check: With power off, turn the drum or tub by hand -- resistance or grinding points to the motor or a bearing, and a cracked, glazed, or snapped belt is visible once the cabinet is open.

Parts in this group on A212: WP211948 (Drive Belt - 120v 50 cycle), WP211451 (Pump Belt).

Storage, trim and cosmetic hardware

Symptom: A cracked shelf, broken door bin, worn hinge, or missing trim piece -- cosmetic and storage wear rather than a functional breakdown.

Check: Match the physical dimensions and mounting tabs of the old part before ordering; these pieces are often model-specific even between visually similar models.

Parts in this group on A212: WPY313561 (SCREW----NA (PART NOT USED-DE).

Door and drum seals

Symptom: A door boot or gasket that's torn or losing its seal, letting water leak out during the wash or spin cycle.

Check: Check the door boot or gasket for tears, especially near the drain hole at the bottom, and confirm it isn't pinched or twisted where it clamps to the drum.

Parts in this group on A212: WP214765 (Syphon Break Gasket).

Suspension and tub hardware

Symptom: Excessive vibration, banging, or the machine "walking" during the spin cycle.

Check: Check that all leveling legs are actually contacting the floor, then inspect the suspension rods or springs for wear or a broken mount point.

Parts in this group on A212: WP215581 (Agitator Shaft Spring).

Before you buy

Match A212 exactly against the model and serial plate on the appliance itself before ordering anything — a single mismatched character can point to a different production run with different parts. Then check the part number printed or stamped on the part you are replacing against the part numbers in the table above; the printed number is the most reliable way to confirm fitment when a model has gone through multiple production runs. RepairKitHub does not sell parts directly — every part link above routes to an Amazon search for that part number so you can compare current listings and sellers yourself.

How to confirm this is your model

On most washers, the model and serial plate sits under the lid or on the back panel. Match every character exactly, including letters and dashes at the end — appliance model numbers often have similar prefixes but different suffixes for different production runs.

Neighbouring Whirlpool Washer models

These model numbers sort next to this one in the catalog and are usually the same product family.

Still not sure?

Use the model lookup tool to search by model or part number, or start from the symptom your appliance is showing.