Parts for A182 — Whirlpool Washer

We found 35 parts confirmed to fit the Whirlpool Washer A182.

Compatibility table

Prices shown are an informational reference range only, not an offer or an Amazon price — RepairKitHub does not sell parts directly. Each part links to an Amazon search so you can compare current listings yourself.

Common failure areas on this model

The confirmed parts above group into a handful of failure areas. Here is what each points to and how to check it before you order anything.

General hardware and mounting parts

Symptom: A small mechanical or mounting part has failed, cracked, or gone missing.

Check: Compare the physical shape and mounting points to the original piece, and confirm the exact part number against your model plate before ordering.

Parts in this group on A182: 205828 (Inlet Hose), WPW10548433 (Clamp), 203956 (Damper Pad Kit), 205134 (Motor Switch), WP211232 (Outer Tub Clamp Seal), WP213045 (Outer Tub to Pump Hose), WP215120 (SEAL FOR I), WP210286 (Seal), 208847 (Syphon Break Elbow Kit with Clamp), WP212716 (Washer Lid Bumper), WP311155 (Wire), 202861 (Carton Of 25), W11129403 (BOLT), WP213013 (Injector Hose), WP213015 (Plastic Injector Nozzle), WP22003441 (Rear Bearing), WP216201 (Rubber Injector Valve), 202860 (Inlet Hose Kit), 200461 (Hose Clamp).

Storage, trim and cosmetic hardware

Symptom: A cracked shelf, broken door bin, worn hinge, or missing trim piece -- cosmetic and storage wear rather than a functional breakdown.

Check: Match the physical dimensions and mounting tabs of the old part before ordering; these pieces are often model-specific even between visually similar models.

Parts in this group on A182: WP22001619 (Air Tube for Tub Fill Volume), WP22213057 (Injector Sleeve Bracket - Side Mounting), WPY313561 (SCREW----NA (PART NOT USED-DE), WP22001650 (Spring Retaining Clip), 202718 (Tension Springs -Set of 2), 214739 (Spring Hose).

Water inlet and drainage

Symptom: A washer that won't fill, fills slowly, won't drain, or leaves standing water in the tub.

Check: For fill problems, check the inlet valve's screen filters for sediment. For drain problems, check the pump for a jammed object and confirm the drain hose isn't kinked or looped too high.

Parts in this group on A182: WP22003410 (Corrugated Drain Hose), WP22001448 (Pump-to-Siphon Break Drain Hose), 206638 (Siphon Break Connector Kit).

Drive system (belts, pulleys, motors)

Symptom: A drum or tub that won't turn, a burning-rubber smell, or a loud thump or squeal during a cycle.

Check: With power off, turn the drum or tub by hand -- resistance or grinding points to the motor or a bearing, and a cracked, glazed, or snapped belt is visible once the cabinet is open.

Parts in this group on A182: 12002351 (Drive Motor - One Speed - 120V), 211125 (Washer Drive Belt), 211124 (Washer Pump Drive Belt).

Door, lid switches and latches

Symptom: The washer won't start, or it stops mid-cycle as soon as the lid is opened.

Check: Listen for an audible click when the lid closes. No click, or a visibly cracked plastic tab on the latch, points to this part.

Parts in this group on A182: WP213720 (Lid Switch Actuator Spring), WP211726 (Washing Machine Lid Hinge Ball).

Door and drum seals

Symptom: A door boot or gasket that's torn or losing its seal, letting water leak out during the wash or spin cycle.

Check: Check the door boot or gasket for tears, especially near the drain hole at the bottom, and confirm it isn't pinched or twisted where it clamps to the drum.

Parts in this group on A182: WP214765 (Syphon Break Gasket).

Controls, timers and wiring

Symptom: A cycle that doesn't advance, the wrong water level filling, an unresponsive display, or the washer not starting at all.

Check: Look for burn marks or a burnt smell near the board or terminals, and check whether buttons and knobs respond -- a unit that powers on but won't cycle often traces back to this group.

Parts in this group on A182: WP211065 (Timer Knob Spring).

Before you buy

Match A182 exactly against the model and serial plate on the appliance itself before ordering anything — a single mismatched character can point to a different production run with different parts. Then check the part number printed or stamped on the part you are replacing against the part numbers in the table above; the printed number is the most reliable way to confirm fitment when a model has gone through multiple production runs. RepairKitHub does not sell parts directly — every part link above routes to an Amazon search for that part number so you can compare current listings and sellers yourself.

How to confirm this is your model

On most washers, the model and serial plate sits under the lid or on the back panel. Match every character exactly, including letters and dashes at the end — appliance model numbers often have similar prefixes but different suffixes for different production runs.

Neighbouring Whirlpool Washer models

These model numbers sort next to this one in the catalog and are usually the same product family.

• A183 — 37 parts
• A18CA — 21 parts
• A18CM — 16 parts
• A18CT — 14 parts
• A190 — 29 parts
• A181 — 45 parts
• A180 — 45 parts
• A17CT — 32 parts
• A17CM — 32 parts
• A17CA — 34 parts

Still not sure?

Use the model lookup tool to search by model or part number, or start from the symptom your appliance is showing.